|
|
| DELTA® MS 500: |
|
DELTA® MS 20: |
 |
Cavity drainage membrane for use on walls and floors, as a waterproof system. A choice of finishes are available. Can also be used externally for waterproof protection of sub-ground structures. |
|
 |
Dimpled sheeting with particularly high drainage capacity and compressive strength, suitable for high performance seepage layers in building and civil engineering construction. |
| Material: |
high density polyethylene |
| Thickness: |
approx. 0.6 mm |
| Stud height: |
approx. 8 mm |
| Roll size: |
available in clear
|
| (With flat edge of 7 cm
on one side) |
2.4 x 20 m |
|
2.0 x 20 m |
| Compressive strength: |
> 250 kN/m2 |
| Drainage capacity: |
approx. 2.25 l/s . m |
| |
approx. 135 l/min . m |
| |
approx. 8 100 l/h . m |
| Air volume between studs: |
approx. 5.3 l/m2 |
| Temperature resistance: |
- 30°C to + 80°C |
| Chemical properties: |
resistant to chemicals, resistant to root
penetration, rotproof, neutral towards
drinking water |
| |
| |
| Behaviour in fire: |
B2 accord. to DIN 4102, in the case of
special requirements possibly B1 accord.
to DIN 4102
(test mark PA III 2.2087) |
| |
| |
|
|
| Material: |
high density polyethylene |
| Thickness: |
approx. 1 mm |
| Stud height: |
approx. 20 mm |
| Roll size: |
2.0 x 20 m |
| |
In the case of special requirements, also available in board format |
| |
| Compressive strength: |
approx. 150 kN/m2 |
| Drainage capacity: |
approx. 10 l/s • m |
| |
approx. 600 l/min • m |
| |
approx. 36 100 l/h • m |
| Air volume between studs: |
approx. 14 l/m2 |
| Temperature resistance: |
- 30 ° C to + 80 ° C |
| Chemical properties: |
resistant to chemicals, resistant to root
penetration, rotproof, neutral towards
drinking water
|
| |
| |
| Behaviour in fire: |
B2 accord. to DIN 4102, in the case of
special requirements possibly B1
accord. to DIN 4102 |
| |
| |
|
 |
Dimpled sheeting with plastic mesh welded on, suitable as a damp-proof base for plaster or shotcrete, e.g., as a seepage layer in tunnel construction, or for repairing basements internally. |
|
 DELTA®-FM is specifically
designed for floor applications,
to combat dampness, and
contamination. The special low
stud profile (3mm) minimises
changes in floor levels but still
provides an air gap to achieve
damp pressure equalisation.
The membrane is a fast-track
application that allows various
floor finishes to be achieved with
zero 'down time'. The R.H. levels
are isolated in the air gap, and
controlled. Delta-FM can be used in new build, remedial or refurbishment projects for
floors, and walls. |
| Material: |
high density polyethylene |
| Thickness: |
approx. 0.5 mm |
| Stud height: |
approx. 8 mm |
| Roll size: |
2.0 x 20 m |
| |
1.5 x 10 m |
| Compressive strength: |
approx. 70 kN/m2 |
| Drainage capacity: |
approx. 5 l/s · m |
| |
approx. 300 l/min · m |
| |
approx. 18 100 l/h · m |
| Void between studs: |
approx. 5.5 l/m2 |
| Temperature resistance: |
- 30°C to + 80°C |
| Chemical properties: |
resistant to chemicals, resistant to root penetration, rotproof, neutral towards drinking water |
| |
| |
| Behaviour in fire: |
B2 accord. to DIN 4102 |
| |
|
|
| Material: |
Virgin high-performance PE-VHD |
| Application: |
Special low stud profile for floor. Can be used on walls |
| Sheet Thickness: |
approx. 0.6 mm |
| Dimple height: |
approx. 3 mm |
| Compressive strength: |
approx 140 kN/m2 |
| Roll Dimensions: |
20m x 2m (40m2) |
| Volume between dimples: |
approx 2.1 1/m2 |
| Service temperature range: |
- 30 ° C to + 80 ° C |
|
|
|
